Hopefully by now you've read through the sections on electric current, resistance, potential and at least ciruits-1, or you're already pretty familiar with electric circuits. Now we'll explore one more important property of electric circuits and circuit elements, the idea of **power**.

Power is the rate at which energy (unit = Joules, J) is transferred through a circuit or a circuit element like a resistor. Remember that kinetic energy, work and potential energy are equivalent and interchangeable. The unit of power is the **Watt** (**W**). One Watt (it's capitalized because it's a person's name) is one Joule per second: **1W = 1J/s** or **1J·s ^{-1}**.

Now recall that electric potential is potential *energy* divided by charge, so if we multiply potential (voltage) by charge and divide by time, we get

Now notice that **q/t** (charge in Coulombs divided by time in seconds) is **current**, so we have

which gives us the most convenient definition of power for electric circuits, **power = voltage multiplied by current**.

While we're here, let's use Ohm's law, **V = IR** to find two other expressions for power in circuits. In the first, we'll replace the potential in the power equation with **IR** from Ohm's law:

For the second, we'll solve Ohm's law for the current and substitute for current in the power equation:

**Power** is the rate at which energy is transferred through an electric circuit. The unit of power is the **Watt**.

1 Watt = 1 Joule per second **1W = 1J·s ^{-1}**

When current flows through a DC circuit in the "natural" direction, that is when electrons originate from the negative pole of the battery, flow through the circuit and terminate at the positive pole, the battery does work on the circuit elements. For example, power can be dissipated in resistors by heating them up.

When current flows the other way, we say that the system is doing work on the circuit, perhaps charging the battery, if that's chemically possible.

Notice that here I'm talking about actual negatively charged current carriers (electrons). Remember that in circuits, for historical reasons, we usually refer to a positive current, and that we don't lose anything by doing so.

A real resistor like this 100 KΩ one (the colored bands are a code for the resistance value) can handle only a limited amount of power. A circuit designer needs to know what that limit is or else she could damage the resistor and possibly the circuit.

For example, a 10 Ω resistor with a maximum rating of 10 W could not be used in a circuit in series with a 12V battery because the power dissipated in it would be **P = IV = V ^{2}/R** = 144/10 = 14.4 W. The resistor might be destroyed.

On the other hand, a 100 Ω 10 W resistor would be fine because **P = IV = V ^{2}/R** = 144/100 = 1.44 W. One way to look at this is that the higher resistance of the 100 Ω resistor slows the flow of current, which reduces the friction between electrons and the atoms of the resistor.

**Power** is **dissipated** in resistors mostly by **heating** them. This is called **resistive heating**.

Let's look at a simple parallel circuit and calculate how much power is dissipated by each resistor. Here's the circuit:

Now the total resistance of the two parallel resistors is

The current through the circuit is

Our resistors are the same, so half of this current flows through each resistor. That's 0.12A through each. The power dissipated by each resistor is:

So we need to be able to handle 1.44 W, but it would be wise to over-design a little bit. I would probably use resistors rated to handle 5 W in this circuit.

If you've just built a sophisticated and expensive electronic circuit, it makes sense to protect it from damage. One of the most common forms of damage to a circuit is having too much power dumped through it. Think of a sudden surge in the power supply in your home.

For this kind of protection, we use **fuses**, circuit elements with something like a thin wire that will burn through and break if more than a limiting amount of power passes through it. A fuse might look something like this.

It has points of electrical contact at both ends and some kind of mechanism for breaking the circuit if too much power passes through it.

The most common symbol for a fuse on paper looks like this. The power rating is generally written below.

Other examples of circuit protection devices include more sophisticated electronic versions, like the ground-fault interrupter plugs in your kitchen or bathroom (that protect you from electrocution around water), or the circuit breakers in your fuse box at home or work.

You can see high-voltage transmission lines like this all over the world. They're how we transport generated electricity over long distances to get to houses and businesses.

The idea of **power loss** in transmission over long distances is crucial here.

Let's say that we generate one megawatt of electricity at a power plant and we want to transmit it 500 miles. It will be used at a potential of 240 V, so we'll transmit it at that voltage. That means we'll need a current of over 4000 Amps:

Source: Wikipedia Commons (cropped)

Now we can use this current to calculate the power loss due to heating of the wire. According to the Aluminum Association, the resistance of one mile of 1-inch diameter aluminum wire with a steel core (typical for high-voltage transmission) is about 0.145 Ω, so the resistance of 500 miles of this wire would be (500 ~~mi~~.)(0.145 Ω/~~mi~~.) = 72.5 Ω.
**P = V**^{2}/R won't work in this case.

The power lost in heating that wire would be

Well, that's more than the power we were trying to transmit, so it means that we wouldn't get any electricity at all on the other end of the wire.

The solution is to transmit the power at a very high voltage. The highest voltage used in the U.S. is 735 KV (735,000 V), which would man a current of **I = P/V** = 1 × 10^{6} / 0.735 × 10^{6} = 1.36A, a much lower current.

Now the power loss would be

which is about 0.01% of the power transmitted. Hopefully you can see why transmitting power at high voltage and low current is the way to avoid transmission loss due to heating of the wire.

Now in practice there are other sources of loss in our power distribution grid, including corona discharge, a phenomenon where, at high voltage, electrons can just jump off of the wire, sometimes causing a bluish glow or crackling of the lines in wet or snowy weather.

Hey, notice that I did not calculate the power loss with **P = V ^{2}/R**. That's because the

**xaktly.com** by Dr. Jeff Cruzan is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License. © 2012, Jeff Cruzan. All text and images on this website not specifically attributed to another source were created by me and I reserve all rights as to their use. Any opinions expressed on this website are entirely mine, and do not necessarily reflect the views of any of my employers. Please feel free to send any questions or comments to jeff.cruzan@verizon.net.